Fluke 2062 Advanced Wire Pro Tracer Product Resources
This article is to provide easy access to online resources for the Fluke 2062 Advanced Pro Wire Tracer. You will find links to useful resources for the 2062 Advanced Pro Wire Tracer below.
Introduction
The 2062 Advanced Wire Tracer is intended for quickly locating energized and de-energized wires in walls, ceilings and floors, finding breaks and opens in wiring, and locating breakers and fuses easily. Patented Smart Sensor™ locates and displays energized wires on the color display.
Quick Reference Guide
Quick Reference Guide
Users Manual
2062 Users Manual
Additional Useful Documentation
Product Specifications
Safety Sheet
How Do Wire Tracers Work?
How To Trace Electrical Wires In Walls
Useful Videos
Fluke 2052 and 2062 Advanced Wire Tracers.
How to trace wire in walls with the Fluke 2052 and 2062 Advanced Wire Tracer.
How to ground the Fluke 2062 and 2052 Advanced Wire Tracer.
Specifications
Specifications: Fluke 2062 Advanced Pro Wire Tracer Kit
| General | 2062R Receiver | 2000T Transmitter | i400 AC Current Clamp |
| Measurement category | CAT IV 600 V | CAT IV 600 V | CAT IV 600 V, CAT III 1000 V |
| Operating voltage | 600 V AC/DC | 600 V AC/DC | 1000 V AC |
| Operating frequency | Energized: 6.25 kHz De-Energized: 32.768 kHz | Energized/Loop: 6.25 kHz De-Energized: 32.768 kHz | N/A |
| Signal indications | Numeric, bar graph display and audible beep | LEDs and audible beep | N/A |
| Response time | Smart Sensor: 500 ms Tip Sensor (Energized/De-Energized): 500 ms NCV: 500 ms Battery monitoring: 5 s | Line voltage monitoring: 1 s Battery voltage monitoring: 5 s | N/A |
| Current output of signal (typical) | N/A | Energized circuit: High mode: 60 mA rms Low mode: 30 mA rms De-energized circuit: High mode: 110 mA rms Low mode: 40 mA rms Loop mode with test leads: 160 mA rms Loop mode with i400 AC Current Clamp: 385 mA rms | N/A |
| Signal voltage output (nominal) | N/A | Energized circuit: High mode: 14 W @ 230 V ac/50 Hz, 3.33 kΩ @ 230 V ac Low mode: 4.6 W @ 230 V ac/50 Hz, 11.5 kΩ @ 230 V ac De-energized circuit: High mode: 31 V RMS, 140 Vp-p, 0.86 W @ 1 kΩ load Low mode: 27.5 V RMS, 120 Vp-p, 0.1 W @ 1 kΩ load Loop mode with test leads: 32 V RMS, 140 Vp-p, 0.87 W @ 1 kΩ load Loop mode with i400 AC Current Clamp: 31 mV, 0.89 W @ 1 Ω load | N/A |
| Range detection (open air) | Smart Sensor Direction Indication Mode ≤15 cm (6 in), 230 V AC, high mode, sensitivity level 2 Tip Sensor: Energized Max distance via air: up to 6.1 m (20 ft) Pinpointing: approx. 5 cm (1.97 in) Tip Sensor: De-Energized Max distance via air: up to 4.5 m (14.7 ft) Pinpointing: approx. 5 cm (1.97 in) NCV (40 Hz to 400 Hz) Max. sensitivity: 90 V up to 2 m Min. sensitivity: 600 V up to 1 cm | N/A | |
| Current range | N/A | N/A | 400 A |
| Basic accuracy | N/A | N/A | 2 % + 0.06 A (45 Hz to 400 Hz) |
| Display | |||
| Display size | LCD 89 mm (3.5 in) | LEDs | N/A |
| Display dimensions (W x H) | 70 mm x 52 mm (2.76 in x 2.07 in ) | N/A | N/A |
| Display Resolution | 480 px x 320 px | N/A | N/A |
| Display type | Color TFT LCD | LEDs | N/A |
| Display color | 16-bit | Operating mode LEDs: red Battery status LEDs: green, yellow, red | N/A |
| Backlight | Yes | N/A | N/A |
| Environmental | |||
| Operating temperature | -20 °C to 50 °C (-4 °F to 122 °F) | -20 °C to 50 °C (-4 °F to 122 °F) | -20 °C to 50 °C (-4 °F to 122 °F) |
| Operating humidity | 45%: -20 °C to <10 °C or 40 °C to 50 °C (-4 °F to <50 °F or 104 °F to 122 °F) 95% (non-condensing): 10 °C to <30 °C (50 °F to 86 °F) 75%: 30 °C to <40 °C (86 °F to <104 °F) | 45%: -20 °C to <10 °C or 40 °C to 50 °C (-4 °F to <50 °F or 104 °F to 122 °F) 95% (non-condensing): 10 °C to <30 °C (50 °F to 86 °F) 75%: 30 °C to <40 °C (86 °F to <104 °F) | 10 °C to <30 °C (95 %: 50 °F to <86 °F) 30 °C to <40 °C (75 %: 86 °F to <104 °F) 40 °C to <50 °C (45 %: 104 °F to <122 °F) |
| Operating altitude | 2000 m (6561 ft) | 2000 m (6561 ft) | 2000 m (6561 ft) |
| Transient protection | N/A | 8.00 kV (1.2/50μS surge) | N/A |
| Pollution degree | 2 | 2 | 2 |
| IP rating | IP 40 | IP 40 | IP 40 |
| Drop test | 1 m (3.28 ft) | 1 m (3.28 ft) | 1 m (3.28 ft) |
| Mechanical | |||
| Power supply | 4 x AA (alkaline) | 8 x AA (alkaline) | N/A |
| Power consumption (typical) | 110 mA | High/low mode: 70 mA Loop mode with Clamp: 90 mA Consumption without signal transmission: 10 mA | N/A |
| Battery life | Approx. 20 h | High/low mode: approx. 25 h Loop mode: approx. 18 h | N/A |
| Low battery indication | Yes | Yes | N/A |
| Fuse | N/A | 1.6 A, 700 V, fast-acting, Ø 6 x 32 mm, 50 kA interrupt | N/A |
| Maximum conductor size | N/A | N/A | 32 mm (1.26 in) |
| Dimensions (L x W x H) | Approx. 277 x 112 x 65 mm (10.92 x 4.43 x 2.55 in) | Approx. 183 x 93 x 50 mm (7.2 x 3.66 x 1.97 in) | Approx. 150 x 70 x 30 mm (5.9 x 2.75 x 1.18 in) |
| Weight | Approx. 0.544 kg (1.20 lb) | Approx. 0.57 kg (1.25 lb) | Approx. 0.114 kg (0.25 lb) |
| Mechanical | 2000ACC Test Lead Accessory Kit |
| Includes | 2x 1 m test leads (red, black), 1x 7 m test lead (green), 2x test probes (black), 2x alligator clips (red, black), 2x outlet blade adapters (red, black), 2x outlet round adapters (red, black) |
| Measurement category | CAT IV 600 V (test leads), CAT II 1000 V (test probes), CAT IV 600 V (alligator clips), CAT II 300 V (outlet adapters) |
| Operating voltage and current | 600 V, 10 A max. (red/black leads), 600 V, 10 A max. (green lead), 1000 V, 8 A max. (black probe) 600 V, 10 A max. (alligator clips), 300 V, 10 A max. (outlet adapters) |
| Operating temperature | 0 °C to 50 °C (32 °F to 122 °F) |
| Operating humidity | 10 °C to <30 °C (95 %: 50 °F to <86 °F), 30 °C to <40 °C (75 %: 86 °F to <104 °F), 40 °C to <50 °C (45 %: 104 °F to <122 °F) |
| Storage temperature and humidity | 0 °C to 60 °C (32 °F to 140 °F), <95% (non-condensing) |
| Operating altitude | 2000 m (6561 ft) |
| Pollution degree | 2 |
| Water and dust resistance | IP 20 |
| Drop proof | 1 m (3.28 ft) |
| Dimensions | Red/black leads: 1 m (3.28 ft), Green lead: 7 m (22.97 ft), Alligator clips: approx. 95 x 45 x 24 mm (3.74 x 1.77 x 0.94 in), Outlet adapters: 72 x 18 x 18 mm (2.83 x 0.71 x 0.71 in) |
| Weight | Approx. 0.4 kg (0.88 lb) |